The control plank is the key control for almost all of your GE washer? s functions. The switches, knobs, and knobs almost all connect to the particular control board. In case it shorts out and about or gets ruined, your machine may start to reduce functionality or can stop working entirely. Models with an electronic readout may also display an error signal telling you when the control table has stopped operating. If you such as fixing your very own appliances, it is a maintenance you can help to make yourself. Order replacement part #WH12X10468 regarding most GE cleaner models. Then follow these steps to be able to uninstall and replace the old control board.
Unplug typically the washing machine.
This is the first step to be able to any appliance repair project. After you have recognized what? s inappropriate with your cleaner, make sure a person unplug it completely so you remain safe from electrical release and shock.
Take apart the washer.
Move the washer away from the wall. You only need enough space to slide the particular top access section back. If an individual have room, attempt to pull the washer away from the wall since little as possible therefore you don? capital t have to detach the particular hoses or convert off the water.
Eliminate the three screws along the returning edge of the top access -panel and the 3 screws along typically the back side of the lean alongside the management panel. Then you can definitely take the top -panel an inch back, which loosens the particular hold on the particular front trim part. Carefully pry the trim free from the tabs and place it aside. Lift typically the top panel? t back edge upwards and then set the complete panel apart.
Remove the control section next. To start out, pull out the cleaning soap drawer in typically the left-hand side plus depress the show at the back of the cabinet to help you remove this entirely. Set this aside. Take away the screw next to typically the detergent drawer real estate. Next, remove the screws along the particular back of the particular control panel system. Also, pry up the top advantage of the gaming console to loosen the control panel. Keep onto the handle panel and click the two locking tabs on the back again of the gaming system inside the washing machine. Once it comes free, don? capital t pull it aside or allow it to drop. Instead, tilt it down so that you can start off to unplug typically the wires.
You can need to disconnect all of typically the wire harnesses connected to the command panel. What you just have to perform is press along the tab on each of your plug. You put on? t have to be able to worry about mixing up them up during reinstallation because every plug has the unique shape. However, in case you? re anxious about working using wiring, require a photo from multiple angles so you have a very visual guide of where each wire harness should go.
As soon as the the control panel is completely detached from your cleaner, move it to a work surface area. This is the part that properties the control panel.
Remove the older control board.
Depart the control screen face down. Take out the screws alongside the perimeter in the control board. There ought to be four. Also, depress the locking navigation bars along the edge with the control board nearest the winding edge of the control panel. Place be difficult to be able to reach, so work with a flathead screwdriver to move typically the tabs. Pull typically the control board out and shift the control panel besides.
Flip the handle board over. Consider washing machines repair regarding all the switches with the front side from the control table therefore you have some sort of visual guide throughout reinstallation. Then start removing each of the buttons and assemblies and so you can maneuver them over in order to the new component. They should end up being relatively loose, therefore don? t apply too much power on the thin plastic parts.
Set up the modern control plank.
Before you decide to put typically the new control table part in the command panel console, mount all of the particular buttons you taken out from the aged part. The more time assemblies will generally have hooks that really must be slid into typically the cutouts on typically the control board in order to provide extra stability. Make sure each of the control keys is installed so they really match the photo guide.
Once the particular buttons are all throughout place, pick way up the control board and tilt this so that it? s nearly perpendicular to the ground. Get in line the particular control board? s i9000 shaft together with the gap in the the control panel. As you do so, wiggle typically the knob a lttle bit thus the shaft aligns with the gap and snaps totally into place. The particular the control panel helps keep the buttons in place, but in the event that you tilt the particular control board too far forward within this step, some involving the buttons may well come loose. in case anything falls misplaced, just reinsert typically the hooks and consider again.
Once the control board canal is in place, cautiously keep both bits held together and even set the handle panel face along. Now you could lock the 2 bits together by softly pressing three fastening tabs into location and retightening typically the four screws about the edge of the control board.
Reassemble the washer.
Very first, orient the control board assembly alongside the top involving the front associated with the washer hence the curved edge is closest to typically the machine. Start insert the wire makes use of into the command board by adhering to the style guide or even by matching every single wire harness in order to the correct stopper.
Next, tilt the control panel back up so it? s i9000 flush with the top front of the washer, and make sure none of the particular wires get pinched. Slide the navigation bars along the base into the slot machines around the right part, and snap the the control panel into place. Next, retighten the screw that is located close to the detergent drawer housing. Also, retighten the anchoring screws over the back associated with the the control panel. Then slide the detergent drawer into place and reattach the top access panel. If you appear at the base of the top access panel, you? ll notice slots regarding the circular pins along the track. The pins need to go through the greater end of the cutout therefore the screen lies flat plus then, when an individual slide the screen forward, lock directly into place against typically the smaller part of the cutout. This element can be difficult, so a visible guide like at the end associated with this video may help.
To accomplish this, arranged the top entry panel carefully over the frame as well as the pins. It have to hand approximately an inch off the back. Before a person slide the -panel forward, press the particular trim into spot on three locking tabs. Then slide the panel frontward and add back again all six screws to hold this in position.
Push your own washer back straight into place and connector it in. Stick to the guide that came with the control board to program the cleaner. Each model provides a slightly different step. As soon as your washer features been programmed, this? s all set to start off a new cycle.